x11
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
x11 [2018/09/15 18:41] – wiki_admin | x11 [2021/09/19 18:00] – external edit 127.0.0.1 | ||
---|---|---|---|
Line 9: | Line 9: | ||
This board is supported by Amix, during install reply ' | This board is supported by Amix, during install reply ' | ||
- | Then use olinit | + | Following commands are from the "UNIX System V Release 4 Amiga Version 2.0 Addendum" |
+ | |||
+ | For 1024x768 mode: **olinit | ||
+ | |||
+ | For 800x600 mode: **olinit -- -tiga -tm 3** | ||
+ | |||
+ | The A2410 is also emulated by WinUAE. | ||
==== What else is there? ==== | ==== What else is there? ==== | ||
- | With the use of drivers from the **Gateway UNIX CD**, certain other graphics cards are supported which may be easier to find (see the hardware page or the readme in the archive for a complete list). Among them is the Picasso II/ | + | With the use of drivers from the [[http:// |
+ | |||
+ | |||
+ | Some history ([[http:// | ||
+ | |||
+ | Klaus currently works at Village Tronic, at was, is and will be responsible for the hardware design of the graphic boards | ||
+ | " | ||
+ | |||
+ | |||
+ | Since long his hobby was AMIX. Having an A2000 with a GVP Series II SCSI adaptor, he wrote support for this adaptor for AMIX. | ||
+ | |||
+ | |||
+ | Also, he wrote about a dozen of very sophisticated X Servers for several graphic boards. Having intented to release this stuff for years, he finally found a place to distribute it on the Gateway! Vol. 2. | ||
+ | // | ||
This has only been tested with a Picasso II+ board using a fully patched 2.1p2a installation. Other supported boards should use the same or very similar procedure. | This has only been tested with a Picasso II+ board using a fully patched 2.1p2a installation. Other supported boards should use the same or very similar procedure. | ||
Line 30: | Line 49: | ||
3. Run olinit and xinit to make sure they are set up on your machine and working. You should be able to bring up the hideous black and white display. Do this also for other user accounts that you wish to be able to use X later (or copy the config files into that user's home directory later). | 3. Run olinit and xinit to make sure they are set up on your machine and working. You should be able to bring up the hideous black and white display. Do this also for other user accounts that you wish to be able to use X later (or copy the config files into that user's home directory later). | ||
- | 4. Download the SVGA Drivers, uncompress them using bzcat AMIX.tar.bz2 | tar -xf - and gunzip the file X11R5_bin.tar.gz using gzip -d X11R5_bin.tar.gz to end up with a file named X11R5_bin.tar. Write this file to an empty tape on your A3070, don't forget to retension/ | + | 4. Download the [[http:// |
5. Copy the file install.svga from the drivers archive to the AMIX machine (put it in your home directory or /tmp) and run it: sh install.svga You can use an MS-DOS formatted 720k floppy to copy the file. On AMIX insert the disk and execute the command mcopy A: | 5. Copy the file install.svga from the drivers archive to the AMIX machine (put it in your home directory or /tmp) and run it: sh install.svga You can use an MS-DOS formatted 720k floppy to copy the file. On AMIX insert the disk and execute the command mcopy A: |
x11.txt · Last modified: 2022/04/15 12:48 by wiki_admin